Jim Gasowski's Farmboy #003-X2 (twice as big!)

Jim built Farmboy #003 back in 2009 and has just completed a version that is twice as big.  Looks great Jim!  I hope to see it at one of the shows soon.

 

Farmboy valve guide lubrication

----------------- Question --------------------- 

Hi Allen

I am slowly building the Farmboy HnM engine and have a question about the valve guides.

Having gone to the trouble of making the valves a nice fit in the guides I wonder where the lubrication comes from, and if no lubrication won't the valve stem get sloppy in the valve guide?

Having lots of fun & learning lots as well.

Thank you for your time.

Regards

David Tredenick

------------------ Answer -----------------------

Hi Allen,

The valve guides need little lubrication. A drop or two on the valve stem every now and then is more than sufficient. With a little oil mixed in the fuel, the intake will also get lube. Also the exhaust valve which moves the most, may (?) get some lube from the unburned lube in the exhaust. After 11+ years I see no wear on mine.

Finally got around to making the sled for Farmboy x2. Should have a pic or two for you next week.

Take care

Jim G

Mark Smith's Farmboy #801

It's sitting on a lazy suzan for the video thus the reason for the vibration.  He says it ran from the very beginning.  Nice work.  Thanks for sharing!

 

Alan Butters' Miser

Alan Butters, from Australia, and his Miser inside a leather lined box.  Fantastic!

 

Farmboy mistake?

 Here's an email I got from Jim G.

-------------------------------------------------------------------------------------------------------------------

Hi Allen,

Was going over the plans that you sent me and I found a mistake. Page 10, Cam shaft / Governor lever pin, Pin length to the cotter pin hole shows .365". If you put that pin through the Cam Shaft (same page) the pin won't clear out of the square to install the cotter pin. I think the dimensions .430" and the length instead of .420" should be about .490". 

Jim G.

--------------------------------------------------------------------------------------------------------------------

Andrew Whale's "Farm Boy" Construction Videos

Andrew Whale, from merry ol' England, has been producing some very good videos of his Farm Boy engine project.  As of this writing he has three videos, each approx 20 minutes long, and he will have many more as his progress continues.

Here's his first video in the series:

Click the link below for his entire Farm Boy playlist on YouTube:

https://www.youtube.com/playlist?list=PLxJNoWSqCTFiDnJKq89k0HV4MQssGbdwN

Enjoy!

PICTIM and Power Keg Coil Bench Testing

Before you install your new PICTIM ignition system on your engine, I highly recommend you do a simple bench test with it and all the components.  This way you will be more familiar with it and see how it actually works.  Otherwise, once installed on the engine, issues sometimes show up such as bad connections and open grounds - making it much more difficult to diagnose the system as a whole.

Once you get it working on the bench, proceed by installing just ONE component at a time on the engine, and re-test.  If it still works, install the next component and re-test.  Repeat until the entire system is installed.  If it quits working after you installed a particular component, then you know you have a connection problem with that component.

See the photos below for how I bench test the PICTIM and the Power Keg coil.

1. The two black coil wires are connected to Coil + and Coil - on the PICTIM (the Power Keg coil is NOT polarized unlike the Universal ATV or other "3 wire" coils)
2. The white leads will simulate the spark plug, so position them so they are 1/16" to 1/8" apart.  No more, no less or you can damage the coil.  If you have the red universal ATV coil; simply position the end of the spark plug wire 1/16" to 1/8" from the coil frame and the spark will jump here.
3. I connect a 9v smoke alarm battery to Batt + and Batt- on the board.  
4. Using a bent paper clip, quickly touch and release positions 1 and 3 on the switch connection block.  This simulates a "points" system.  Each time you make a connection you should see the LED light up and a spark jump across the white wires of the coil.

(click photos to enlarge)

If this is successful, and if your setup will be using the Hall/Magnet switch, then resume testing:

1. Disconnect Batt +.
2. Hook up the Hall sensor directly to the switch block following the PICTIM wiring diagram PDF, or alternatively use steps 3-7:
3. Gently bend the middle lead of the Hall sensor away from the other two.
4. Wrap a small strip of tape around the two outer leads as close to the head as possible, leaving half of the bottom of the leads exposed.
5. With the Hall bevel facing up and leads towards you, bend the middle lead 2 to the left so it is now "third" from the right.  Lead 1 should still be straight and will now be "second".  Lead 3 will also be straight and "first" from the right.
6. The tape serves as an insulator in case the leads touch.  Verify that the bent middle lead is not touching and other leads.
7. Insert the Hall sensor into the terminal block, face up, into block positions 1,2,and 3 as shown in the photo below:



(click to enlarge)

8. Reconnect Batt +.

Wave your magnet's south pole across the face of the Hall sensor.  At each pass, the LED should light and a spark should jump between the coil's white leads.

Final Test:

As a final test before you install anything on your engine, connect the spark plug to the coil.  In the case of the Power Keg, simply connect one white wire to the top of the spark plug, and the other white to the bottom threads.

If you are using the red universal ATV coil, simply connect the coil spark plug wire to the top of the spark plug, and connect the frame of the coil to the spark plug threads.

When you test the PICTIM now, you should see the spark in the spark plug gap.  If not, check connections, or you may have a faulty spark plug.

-----------------------------------------------------------------------------------------------------------------------

If these test pass, you are ready to install the system on your engine.  I would install the components in the following order, testing that everything still works IN BETWEEN each component install:

1. Spark Plug
2. Points or Hall/Magnet 
1. Make sure the Hall sensor install, and it's wires, are well insulated from the engine frame.  Some of our instructions recommend you also ground the module (from the "Gnd" on the board terminal block) to the engine frame.  This is to provide a path for the coil's high voltage to ground in case the Hall sensor or wiring is too close to the engine. If you're getting good spark after installing the spark plug, hold off on this step.  However, if your have a problem with Hall sensors blowing out, try this ground.
3. PICTIM module
4. Battery

If these steps are followed, you are much more likely to have a trouble-free install.  If you have any trouble along the way and just can't figure it out, feel free to e-mail allen@outpostenterprises.com with photos and a detailed description of the problem, and I will do my best to assist.

Good luck!